Osman Bodur
Osman Bodur portresi

Dr.techn. Osman Bodur, MSc.

Senior Scientist | Ar-Ge Proje Yöneticisi

Üretim Mühendisliği ve Fotonik Teknolojiler Enstitüsü, TU Wien

Araştırma

İmalat metrolojisi

İmal edilen parçaları mikrometre düzeyinde ölçmek ve bu ölçümleri toleranslar, süreçler ve kaliteyle ilgili kararlara dönüştürmek.

Genel bakış

İmalat metrolojisi, arkasında çok şey olan basit bir soruyu yanıtlar: parça teknik resmine uyuyor mu? Talaşlı imalat parçalarından minyatür dişlilere ve tıbbi parçalara kadar boyutları, formu ve yüzey dokusunu ölçmek için bilgisayarlı tomografi, koordinat ölçme makineleri, lazer interferometrisi, konfokal ve odak değişimli mikroskopi ile 3B tarama kullanıyorum.

Sorunun ikinci yarısı teknik resmin kendisidir. Geometrik Ürün Spesifikasyonu (ISO GPS), toleransların nasıl yazılacağını ve nasıl doğrulanacağını tanımlar. Onu tasarım, imalat ve muayene arasında ortak dil olarak kullanıyorum, TU Wien'de dersini veriyorum ve bir Austrian Standards komitesinde görev yapıyorum.

Ölçüm, ancak üretime geri beslendiğinde karşılığını verir: istatistiksel proses kontrolü, bilgisayar destekli kalite güvencesi ve parçayla birlikte taşınan ölçüm verileri.

Konular

  • Bilgisayarlı tomografi ve koordinat ölçme makineleriyle boyutsal ve geometrik ölçüm
  • Yüzey dokusu ve Ra, Rq, Rz gibi pürüzlülük parametreleri
  • ISO GPS, toleranslandırma ve doğrulama
  • Kalite güvencesi, istatistiksel proses kontrolü ve bilgisayar destekli kalite (CAQ)
  • Eklemeli imalatla üretilen ve minyatür parçalar için metroloji

Deneyin

Örnek pürüzlülük profili: 4 mm boyunca Ra 0,80 µm, Rz 4,39 µm.

Konumu ve yüksekliği okumak için prob ucunu profil boyunca hareket ettirin. Ra, ortalama çizgiden mutlak yükseklik sapmalarının aritmetik ortalamasıdır. Rq, bu sapmaların karelerinin ortalamasının kareköküdür. Rz, beş örnekleme uzunluğundaki en büyük tepe-vadi yüksekliklerinin ortalamasıdır.

Sorular

Ra ile Rz arasındaki fark nedir?
Ra, bir profilin ortalama çizgisinden tüm sapmalarının ortalamasını alır; bu yüzden tek bir çizik değeri pek değiştirmez. Rz ise her örnekleme uzunluğundaki en yüksek tepeyi ve en derin vadiyi alıp bu değerlerin ortalamasını hesaplar, dolayısıyla aykırı değerlere tepki verir. Aynı Ra değerine sahip iki yüzeyin Rz değerleri çok farklı olabilir.
3B yazıcıyla üretilen parçalar neden bilgisayarlı tomografiyle ölçülür?
Bilgisayarlı tomografi, parçayı kesmeden içini gösterir. İç kanallar, kafes yapılar ve gözeneklilik, dış geometriyle birlikte tek taramada ölçülebilir.

İlgili projeler

  • HDrawing

    Teknik resim öğretiminde, artırılmış ve sanal gerçeklikle desteklenen hibrit eğitim uygulamaları.

    Erasmus+ KA220-VET, proje yöneticisi

    Devam eden 2024 - 2027

Bu konudaki yayınlar 18

2026
Influence of drilling parameters on hole quality in the aluminum alloy AA6013-T651 Özsoy, N., Akşen, T. A., Bodur, O., Poszvek, G. and Özsoy, M. Materials Testing, 68(7), 1296-1310. PDFDOI 10.1515/mt-2026-0025reposiTUm2 atıf
2026
Engineering Graphics Literacy and Manufacturing Performance: A Cross-National Mixed-Methods Study of CAD Competency Gaps, Standards Compliance Deficiencies, and Their Industrial Consequences Sarıkaya, M., Karabulut, Ş., Bodur, O., Okyayuz, A. Ş., Boztunç Öztürk, N. and Dağlı, S. Applied Sciences, 16(10), 4771. PDFDOI 10.3390/app16104771reposiTUm1 atıf
2026
Evaluation of Dimensional Precision in FDM 3D-Printed Parts via Computed Tomography Craciun, R., Maxim, A., Muresan, V., Bodur, O., Walcher, E. M. and Poszvek, G. Acta Technica Napocensis, Series Applied Mathematics, Mechanics, and Engineering, 60(II). reposiTUm
2026
Integrated Study of Surface Roughness Parameters and Dimensional Accuracy in FDM 3D-Printed Rakos, P. G., Dan, I.-M., Walcher, E., Bodur, O. and Poszvek, G. Acta Technica Napocensis, Series Applied Mathematics, Mechanics, and Engineering, 69, 615-629. reposiTUm
2026
Microscopic Fiducial Markers for Industrial Metrology Applications Bleicher, F., Nacu, C., Bodur, O. and Poszvek, G. Acta Technica Napocensis, Series Applied Mathematics, Mechanics, and Engineering, 69, 397-403. reposiTUm
2025
Hybrid Predictive Modelling of Surface Roughness in DMLS AlSi10Mg: Integrating Thermo-Mechanical Simulation and Optical Metrology on ISO 10791-7 Components Bodur, O., Kossik, P., Poszvek, G. and Bleicher, F. Proceedings of the 13th UTIS International Congress on Machining, pp. 1-12. reposiTUm
2025
Quality in Production and Service Bodur, O., García, Á. M., Poszvek, G. and Durakbasa, N. M. Sustainable Green Conversion: Selected Papers from ISPR2024, Springer, pp. 509-531. DOI 10.1007/978-3-031-83583-4_36reposiTUm2 atıf
2025
Seminar für Fertigungsmesstechnik und Qualitätssicherung FQS2025 Bleicher, F., Bodur, O., Poszvek, G. and Trautner, T. F. Konferans sunumu, FQS2025, Vienna, 18 Mart 2025. reposiTUm
2024
Advanced Quality Assurance of Additive Manufacturing Through Computed Tomography Jałowiec, M., Walcher, E. M., Bodur, O., Poszvek, G., Klein, M. and Bayrakçıl, M. D. Industrial Engineering in the Industry 4.0 Era: Selected Papers from ISPR2023, Springer, pp. 179-199. DOI 10.1007/978-3-031-53991-6_14reposiTUm3 atıf
2024
Characterization of Polyethylene Pipe Properties Through Advanced Metrology Techniques Bayrakçıl, M. D., Bodur, O., Klein, M., Walcher, E. M., Poszvek, G. and Jałowiec, M. Industrial Engineering in the Industry 4.0 Era: Selected Papers from ISPR2023, Springer, pp. 97-115. DOI 10.1007/978-3-031-53991-6_8reposiTUm1 atıf
2023
Quality Assurance of Composite Grinding Bodur, O., Walcher, E. M., Brier, J., Krall, S., Bleicher, F., Sterca, A., Sauprigl, J. and Peherstorfer, H. Procedia CIRP, 118, 590-595, 16th CIRP Conference on Intelligent Computation in Manufacturing Engineering. PDFDOI 10.1016/j.procir.2023.06.101reposiTUm2 atıf
2023
Generative design, evaluation and validation of additive miniaturized-manufactured components, based on GPS and quality standards, by high precision measurement technologies Bodur, O. Doctoral dissertation, TU Wien. PDFDOI 10.34726/hss.2023.113420reposiTUm
2022
Improving the Precision of an FDM 3D Printer with Compensation Technique Bodur, O., Sterca, D.-A., Sulz, C. and Walcher, E. M. Smart and Networked Manufacturing, Vol. 5, ed. F. Bleicher, pp. 109-113. reposiTUm
2021
Evaluation of Fused Deposition Modeling Process Parameters Influence on 3D Printed Components by High Precision Metrology Sterca, D.-A., Calin, R.-A., Cristian, L., Walcher, E. M., Bodur, O., Ceclan, V., Grozav, S. D. and Durakbasa, N. M. Digitizing Production Systems, Springer, pp. 281-295. DOI 10.1007/978-3-030-90421-0_24reposiTUm5 atıf
2020
Precision in Additive Manufacturing, Optimization and Evaluation of the Accuracy of 3D Printer based on GPS System Bodur, O., Stepanek, V., Walcher, E. M. and Durakbasa, N. Proceedings of the 31st DAAAM International Symposium, DAAAM International, pp. 963-972. PDFDOI 10.2507/31st.daaam.proceedings.134reposiTUm12 atıf
2020
Intelligent Design and Advanced Precision Metrology on the Geometrical Structure of Medical Needles Based on GPS and ISO Standards Bodur, O., Poszvek, G., Walcher, E. M., Durakbasa, N. M. and Bauer, J. M. Digital Conversion on the Way to Industry 4.0, Springer, pp. 346-362. DOI 10.1007/978-3-030-62784-3_29reposiTUm3 atıf
2019
Additive Miniaturized-Manufactured Gear Parts Validated by Various Measuring Methods Durakbasa, M. N., Demircioglu, P., Bauer, J. M., Bögrekci, I., Bas, G., Bodur, O. and Poszvek, G. Proceedings of the 12th International Conference on Measurement and Quality Control: Cyber Physical Issue, Springer, pp. 276-290. DOI 10.1007/978-3-030-18177-2_25reposiTUm10 atıf
2019
Challenges of Miniaturizing a Precision Gear Durakbasa, M. N., Bauer, J. M., Bodur, O. and Poszvek, G. Proceedings of the International Symposium for Production Research 2018, Springer, pp. 239-253. DOI 10.1007/978-3-319-92267-6_21reposiTUm8 atıf
37 yayın, sunum ve raporun tümü